I am laying out a a course for a 10/20/30 km race; it's a multi-loop course with a single loop of approximately 10km (there's an out & back section that can be adjusted to make the loop distance correct).
The problem is the runners will finish slightly outside the loop in the driveway of the race HQ building. If the course is adjusted lot make the loop 10km including that finish strip, the 20 & 30Kers will be short by that distance. So here's my solution:
Assume for simplicity the road course is 6 miles and the driveway is 0.2. That makes it perfect for the 10k runners, but those in the longer 2 races will be short by that distance on one or two of their loops.
So, for the second and third loops, we extend the turnaround by 0.1. That gives them an extra 0.2 on their second and third loops, plus the finish into the club makes 12.4 or 18.6.
So we'd have to indicate "First Loop Turnaround" and "2nd/3rd Loop Turnaround" but otherwise the loops would be identical. And since the distance we're dealing with on the driveway is actually only about 40-50m the turnaround would be only half that distance past the first loop TA. Have I thought this through correctly?
Sent from my iPad
Multi-loop course layout question
Jim,
No matter what you do, you will have to issue three certificates.
Gene
No matter what you do, you will have to issue three certificates.
Gene
No matter what you do, it is likely that fast runners completing their lap 2 will arrive at the TA just as the slow runners are finishing their lap 1. Similarly for laps 2 vs lap 3.
It will be necessary to find a way to keep the runners sorted.
It will be necessary to find a way to keep the runners sorted.
The Turnaround comes very early on the loop (2km) so that shouldn't be an issue. But am I right in thinking the longer TA will suffice for both the second and third loops?
If all three races are to start simultaneously, why not have three start lines, each offset by the proper distance?
This could screw up split marks, but if it's a small loop the runners may be counting laps, not distance.
This could screw up split marks, but if it's a small loop the runners may be counting laps, not distance.
The problem with that is that some runners change their minds mid-race and opt for a shorter distance. The solution we came up with was to make the loop exactly 10km and make the start and finish lines the same. With chip timing this will allow us to give runners their splits for each loop as well.
The other problem with multiple start lines and a simultaneous start is that you force the fast runners in the 30k to pass all the back-of-the-packers in the other 2 races.
Jim, I have faced this situation a number of times. If you can do it, I think the best solution is to set your loop to be 10K in length, and set the finish line (on its own "finish stretch") so that running to the finish line is equivalent to completing the loop.
That way you don't have these dodgy situations out on the course, and the questions of which turnaround, which finish, which start, etc. Start, finish, turnaround is the same for all runners and the only difference is how many loops they run before the finish.
I know, you can't always have it that way but if you can it works well.
That way you don't have these dodgy situations out on the course, and the questions of which turnaround, which finish, which start, etc. Start, finish, turnaround is the same for all runners and the only difference is how many loops they run before the finish.
I know, you can't always have it that way but if you can it works well.
Jim:
I checked your logic, geometry, arithmetic (whichever) and found your 10K, 20k and 30k to be the correct distances if laid out as you describe.
10K => loop with TA and "tail" to finish
20K => loop with TA moved 0.1-mi from 10K TA plus "same "tail"
30K => same loop and TA as 20K plus same "tail"
All use the same start and finish. Only the 20K TA is different.
We got another inch or 2 last night. I now have 14 courses to measure if I can ever again see the edges of the roads on the routes.
Good luck
Pete
I checked your logic, geometry, arithmetic (whichever) and found your 10K, 20k and 30k to be the correct distances if laid out as you describe.
10K => loop with TA and "tail" to finish
20K => loop with TA moved 0.1-mi from 10K TA plus "same "tail"
30K => same loop and TA as 20K plus same "tail"
All use the same start and finish. Only the 20K TA is different.
We got another inch or 2 last night. I now have 14 courses to measure if I can ever again see the edges of the roads on the routes.
Good luck
Pete